The Join Signet
$138.00
The House Form, carried on the hand.
Round face, 11mm · band tapers to 3mm
Description
The House Form, carried on the hand.
Where the Entwined Signet signs, the Join Signet holds. The face carries the two interlocking arcs in relief — a joining you can run a thumb over without looking.
Some people wear it for a person. Some for a decision. It keeps both confidences equally well.
Materials
- Sterling Silver 925, or 18K Gold Vermeil (2.5 micron minimum) over Sterling Silver 925 — or the two metals together
- Relief-cast face
- Hand-planished band
- Made to order · hand-finished in Bali
Round face, 11mm · band tapers to 3mm
Provenance
Every Cœura piece is made in one atelier in Bali, the same workshop, and in many cases the same hands, we have worked beside for twenty-five years. Your piece is cast, finished and hallmarked there, for you alone.
Care & delivery
Every piece is made by hand and may vary slightly from the images. Made to order, shipped tracked and insured. Every piece is made for you after you order. If it isn't right when it arrives, you can return it within 14 days for store credit. You have 48 hours after ordering to cancel for a full refund. The full terms are in The Keep Promise.
CŒURA · 925 Hand-finished Bali
Made in Bali, in the atelier we have worked beside for twenty-five years. The Atelier
Sizing
Find your ring size
Rings are the hard part, and we'd rather solve the fit before than after.
Before you print
Print the sizer with scaling turned off, so the page comes out at actual size. Choose "Actual size" or "100%", never "Fit to page" or "Shrink to fit". The sheet is US Letter, 8.5 × 11 inches.
To be sure it printed true, hold a ruler against the marker on the sheet. It should measure exactly one centimetre, matched along the ruler. If it doesn't, print again.
Check it on the printed sheet, not on screen. Screens vary in scale, so the marker only tells the truth on paper.
How to use the ring sizer
- Cut out the ring sizer along the dotted lines.
- Make a slit across the dotted line marked "cut here".
- Wrap the sizer around the finger you want to size, numbers facing outward.
- Insert the pointed end through the slit at the opposite end.
- Pull it through until the fit is snug, not tight.
- The number that lines up with the slit is your size.
- Match that size to your piece when you order.
Print the ring sizer Opens the PDF. Remember: actual size, no scaling.
Or use a ring that already fits
Set a well-fitting ring on the printed sheet and match its inside edge to the outside of a circle. The table below is the same measurement, if you already know the diameter.
| US | Inside ø | US | Inside ø | US | Inside ø |
|---|---|---|---|---|---|
| 3 | 14.1 mm | 6½ | 16.9 mm | 10 | 19.8 mm |
| 3½ | 14.5 mm | 7 | 17.3 mm | 10½ | 20.2 mm |
| 4 | 14.9 mm | 7½ | 17.7 mm | 11 | 20.6 mm |
| 4½ | 15.3 mm | 8 | 18.1 mm | 11½ | 21.0 mm |
| 5 | 15.7 mm | 8½ | 18.5 mm | 12 | 21.4 mm |
| 5½ | 16.1 mm | 9 | 18.9 mm | 12½ | 21.8 mm |
| 6 | 16.5 mm | 9½ | 19.4 mm | 13 | 22.2 mm |
For the best fit
- Wider bands feel snugger. For The Band, Wide we recommend about a half size up from your usual narrow-ring size.
- Measure at a normal time of day. Fingers change slightly with temperature and time, and one hand differs from the other.
- Between sizes? Start with the larger of the two, and check the fit note on the piece itself.
- We confirm before the bench. For commissioned rings we email to confirm your size before your piece is made; simply reply if it isn't right.
Still unsure? Write to hello@shopcoeura.com and we'll help you measure. More in our Sizing guide.